Initial release with Docker version 1.3.3. Simple Syncthing doesnt need IP addresses or advanced configuration: it just works, over LAN and over the Internet. The docker version is maintained by LinuxServer.io. The folder '/shared' of Syncthing binds to shared folder root of NAS, you can add other shared folder as sync folder in Syncthing.ģ. The default folder '/config' of Syncthing binds to '/share/Docker/Syncthing/config'.Ģ. Your data is your data alone and you deserve to choose where it is stored, whether it is shared with some third party, and how it's transmitted over the internet.ġ. It synchronizes files between two or more computers in real time, safely protected from prying eyes. Syncthing also embraces an effective and safe Block Exchange Protocol (BEP), works over local networks and the Internet, and provides an intuitive interface. Not great, not terrible, but could be better.Syncthing is a continuous file synchronization program. If you're running on an oddball system such as a NAS, please consult your vendor.
Syncthing over internet download#
Right now one my my go to things for big transfers is to shutdown syncthing on desktop and laptop, rsync data over ethernet cable and start them again, so they have matching mtime on both ends, when syncthing scan them, it detects them as synced. 64-bit (x86-64) If you are unsure what to download and you're running on a normal computer, please use the 64-bit (x86-64) build for your operating system.
Syncthing over internet free#
When I add a lot of data, like, dump few new CDs into ~/music, all my devices using WiFi starts syncing, meaning, which result in about 3-5 MBps per device, if I could at least sync desktop and laptop over ethernet, that would free bandwidth for my other devices like tablet and phone to get them faster, since my bottleneck is Wireless network with all the issues it bring, like channel saturation, obstacles. I have desktop and laptop accessing the Internet using wireless network, meaning communication between laptop and desktop goes via router, while router is AC and support MU-MIMO, however I cannot get more than 10-15 MBps when tested with iperf3, when one of the device is hooked via ethernet into router, I can get about 30 MBps with iperf3 peerrouterpeer2, however using using ethernet cable between desktop and laptop I can get about 101-110 MBps using iperf3, which is like 10x the speed I can get on WiFi in regard to data transfer. file creation, modification, and deletion etc. The device could be a desktop system, server, or a mobile phone. Would be great if syncthing could either have API endpoint that I could POST to, to make attempt to re-connect already connected peer, or if syncthing could retry connection to entries IF currently connected entry is not the first one (as in, address priority support).įor now I just keep restarting syncthing, however it seems to be prone to race condition, when my laptop is reachable over both WiFi IP and ethernet IP, sometimes it does still connect to peers over WiFi, seems like it's because the remote peer connected to my laptop over WiFi IP before my laptop's newly restarted instance of syncthing connected to remote peer over ethernet (as in order of address entries)Īlso, I am still skeptical the difference in wired vs wireless is significant enough to go through this hassle all together. Syncthing is a free, opensource, peer-to-peer (P2P) file synchronization program that allows you to securely synchronize files between two or more devices within LAN or remote devices over Internet.
![syncthing over internet syncthing over internet](https://www.topbestalternatives.com/wp-content/screenshots/syncthing-25157-3.jpg)
The problem: currently syncthing have no logic to re-connect or re-discovery peers unless it actually loose connection to a peer, this means that to switch it over to ethernet network from WiFi I need to restart syncthing, this however also trigger rescan of all directories and is quite expensive. I have all the devices that can use ethernet configured inside Syncthing with 2 address entry, first is the tcp://on-ethernet-ip, second is the 'dynamic' string
![syncthing over internet syncthing over internet](https://ostechnix.com/wp-content/uploads/2020/11/Synchronize-Files-Between-Multiple-Systems-With-Syncthing-585x390.png)
Goal: I'd like to be able to plug my laptop into ethernet cable and make syncthing use ethernet over WiFi connection for the hosts that are present on said network. Wireless network: 192.168.0.0/24 (has internet, all hosts connected to it) always connectedĮthernet network: 172.17.17.0/24 (no internet, only 3 hosts present in this network) connected ad hoc I'd like to be able to switch to wired connection to some peers when connected to said ethernet network. Use case: I have a home WiFi network that I use syncthing over, I also have separated ethernet network with different subnet that some of my devices are present.